ANVER Vacuum Lifters, Vacuum Cups, Vacuum Pumps, Vacuum Tube Lifters, Vacuum Sheet and Plate Lifters, Vacuum End-EffectorsVacuum Check Valves for Vacuum Systems
 Used in Virtually Every Vacuum Application Shown on Our Website
 New, improved designs, competitively priced and leak-proof – specially made by ANVER in the USA.

We have built our own due to the lack of suitable check valves for our type of vacuum applications.
ANVER CheckVacs offer the best combination of features for our industry, making them the best overall value.

PDF for Vacuum Check Valves View Printer-Friendly PDF Page

Vacuum Check Valves Improve Vacuum System Performance

For Industrial Vacuum Applications Requiring High Flow:

ANVER one-way vacuum check valves are suitable for all vacuum applications, where vacuum loss prevention is required. The check valves can operate in any position, making them suitable for all vacuum needs. We designed them to be leakproof, and to have a low cracking pressure and the highest flow available. Made in the USA by ANVER.

Features that make CheckVac valves the best for vacuum applications:

  • One-piece airtight aluminum body in a compact design. No seams means no leakage – two-piece valves that screw together risk possible leakage. The anodized aluminum body will not crack as may plastic valves when being screwed into a fitting.

  • Optimum flow design for all vacuum applications – a very large Flow Rate (CV).  This allows more suction flow and eliminates the major source of flow restriction in most vacuum systems. This is an easy performance upgrade which offers the best results for the money.

  • Spring loaded, so they operate in any orientation. The low cracking pressure allows you to get the most performance from your pumps; does not waste your pump's power opening the check valve.

  • Precision internal plastic valve with stainless steel springs – eliminates corrosion from water contamination.

  • Note: On the 3/8" check valve we used a 1/2" check valve with adaptors. This allows for a maximized flow rate (CV) in this popular size. Try it on any 3/8" hosed system; you will find that the reduced restriction is worth the minimal added cost of adaptors. The 1" is a 1 ¼" with adaptors and the 1 ½" is a 2" with adaptors. Again, the reason for this is to maximize flow.

  • Remember: The main restriction of a vacuum system is at the check valve. You can utilize a smaller pump if you increase flow at this point. This is the most economical way to increase a vacuum system's performance.

CheckVac Aluminum Vacuum Check Valve Specifications:

Maximum Pressure: 230 psi
Temperature: 0° to 200° F (-18° to 93° C)
Seals: Nitrile Butadiene Rubber

Product Photo
(Click to
Enlarge)

Part No.

Pipe Thread

Height
in.
(mm)

Hex Size
in.
(mm)

 Cracking Pressure*

Flow Rate
(Approx. Cv)
in. Hg
(mm Hg)		 psi

CV14F14F CV14F14F 1/4" NPT (Female)
x
1/4" NPT (Female)		 1.38
(34.9)		 11/16
(17.5)		 0.58
(14.73)		 0.28 (± 0.14) 1.15

CV38F38F CV38F38F 3/8" NPT (Female)
x
3/8" NPT (Female)		 - 1.00
(25.4)		 0.60
(15.24)		 0.30 (± 0.14) 4.4
FB12X38 FB12X38
Adapter used with
CV12F12F (below)
to make CV38F38F (above)		 1/2” NPT (Male)
-
3/8” NPT (Female)		 0.56
(14.3)		 - - - -

CV12F12F

CV12F12F

1/2” NPT (Female)
x
1/2” NPT (Female)

2.44
(61.9)

1.00
(25.4)

 0.60
(15.24)		 0.30 (± 0.14) 4.7

CV34F34F 3/4" NPT (Female)
x
3/4" NPT (Female)		 2.75
(69.9)		 1.187
(30.2)		 0.52
(13.21)		 0.26 (± 0.14) 10.8

CV114F114F 1 1/4" NPT (Female)
x
1 1/4" NPT (Female)		 3.38
(85.9)		 2.00
(51.8)		 0.14
(3.56)		 0.07 (+0.14/-0.05) 28

CV2F2F 2" NPT (Female)
x
2" NPT (Female)		 5.00
(127.0)		 - 0.35
(8.89)		 0.17 (± 0.14) 63

CV12M12F 1/2" NPT (Male)
x
1/2" NPT (Female)		 1.6
(40)		 1.2
(30.2)		 0.60
(15.24)		 0.30 (± 0.14) 4.7

* Cracking Pressure refers to the minimum pressure differential needed between the inlet and outlet of the valve to lift the plunger off its seat to generate flow.

NOTE: These check valves were designed and built specifically for our vacuum lifting systems, and have been proven in actual vacuum system installations. Ordinary check valves designed for compressed air systems are unsuitable for use in vacuum systems and can adversely affect your system.