ANVER
Model JTZSE Digital Control Switch For Non-Corrosive Gases
Non-Corrosive Gases Model [Compound and Low Pressure]. This popular standard
model is a compact multi-purpose
compound pressure gauge specifically designed to cover negative to normal pressure.
A Rear
Mount Bracket option is available.
ANVER
Model JTZSE-R2 Digital Control Switch
For Liquids or Gases
This special High Corrosion Resistant Model [Compound and Absolute
Pressure] has pressure port
attachments made of SUS 316L stainless steel for exact, accurate pressure control to cover a
broad range of applications.
Features:
Full 3-digit red LED display - gives a clear indication even in low
light locations
Proven
IP65 grade gauge body is suitable for industrial installations
Small,
space-saving 30mm square face design
2-point
switch output with a total of eight operation modes possible
Analog
output 1-5V in addition to the 2-point switch output
8
different pressure units are available for selection
Digital Vacuum
/ Pressure Control Switches Specifications
Model
No.
Pressure Port
Diaphragm Material
Net Weight (Including
2 m cable)
Accessories
JTZSE
Aluminum die-casting Rc 1/8
female, 2 places
Silicone,
Single Crystal
Approx.
80 g
Unit Seal, Seal Screw,
M5 Connecting Joint Screw
JTZSE-R2
Mounting: R 1/4,
with M5 Female
SUS316L
Approx.
150 g
Unit
Seal
Pressure Reference: Gauge - Pressure Setting Range
Model
No.
Rated
Pressure Range
kPa
gf/cm
sq
mmHg
mbar
psi
Breakdown
Pressure
JTZSE
-100 to 1000 kPa
-999 to
999
-999 to 999
-760 to 760
n/a
-14.5 to 14.5
500 kPa
JTZSE-R2
-100 to
100 kPa
-99.9 to
99.9
-999 to 999
-760 to 760
-999 to 999
-14.5 to 14.5
300 kPa
Switch Output
Model
No.
General
Specifications
Hysteresis
Repeatability
Response
Short
Circuit Protection
JTZSE
2-Point Output, NPN/PNP transistor open collector, Capacity: 30 V Dc 100 mA max.,
Residual Voltage: 1.2 V or below (At load current of 100 mA)
0 - 300 digits (adjustable)
+/- 0.2% F. S. +/- 1 digit
5 ms maximum
Provided
JTZSE-R2
Output
Mode Setting (Detected Pressure - Pin)
Model
No.
Output
Mode
R Mode
G
Mode
V Mode
Output
Voltage Vo
JTZSE
Pin
(H)
+Pr
-Pr
-Pr
Vo(H)
JTZSE-R2
Pin
(L)
-Pr
O
O
Vo(L)
Environmental Characteristics
Model
No.
Protection
Grade
Operating Temp. Range
Storage Temp. Range
Operating
Humidity
Insulation Resistance
Dielectric
Strength
Vibration
Shock
JTZSE
IP65 (Pressure Gauge Body): Conforming to IEC
14° to 122° F
(-10 to 50° C)
68° to 158° F
(20° to 70° C)
35 to 85% Relative Humidity
More than 100 M ohm at DC 500 V between wire
bundle and pressure port
One minute at AC 500 V between
wire bundle and pressure port (Leak current:
Less than 1mA)
10-55 Hz Amplitude 0.75 mm, 3 directions, 2h each
+/-3% F. S. (0 ± 50 degrees C)
JTZSE-R2
General
Model
No.
Analog
Output
Display
Negative
Pressure Display
Switch State Indication
JTZSE
Output Voltage: 1 -5 V (Zero point 1V ± 0.2 V Span 4 V ± 0.2 V)
Output Impedance: 10k ohm
Resolution: 1/204
Full 3 digit LED (Sampling Cycle: 4/second)
Negative Pressure LED is on
Output
1 (green) and output 2 (red) light up when
output is on: Thermal Error
View Printer-Friendly PDF Page
