| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
View Printer-Friendly PDF Page|
ANVER Vacuum Lifters can be outfitted with a variety of Interchangeable Vacuum Pads and Vacuum Lifting Attachments for a wide range of material handling applications. The below Vacuum Lifting Pad Attachments feature ANVER's proprietary SSR Series of Hand Replaceable Slip-On Vacuum Sealing Rings. With SSR Sealing Rings, ANVER Vacuum Lifters are more economical to operate as the vacuum seals can easily be replaced in minutes with no tools required for removal or installation. ANVER SSR Sealing Rings also feature a short lip design for rapid vacuum attachment and release. |
|
Single Pad Vacuum Lifting Attachments |
|||||||
| Product Photo (Click to Enlarge) |
Vacuum Lifting Attachment No. |
With M83M Generator | With Other Generators |
Headroom Added to Generator (Bottom of Pad to Mounting Holes) in. (mm) |
Vacuum Seal No. |
Vacuum Seal Dia. in. (mm) |
|
| Rated Load Capacity* (Horizontal) lb (kg) |
Rated Load Capacity* (Horizontal) lb (kg) |
Rated Load Capacity* (Vertical) lb (kg) |
|||||
 |
PA70-S-3 | 150 (68) |
160 (73) |
80 (37) |
2.75 (70) |
SSR-70 | 7.13 (181) |
 |
PA80-S-3 | 200 (91) |
220 (100) |
110 (50) |
2.75 (70) |
SSR-80 | 8.25 (210) |
 |
PA90-S-3 | 250 (114) |
275 (125) |
137 (63) |
3.75 (95) |
SSR-90 | 9.25 (235) |
 |
PA119-S-3 | 500 (227) |
500 (227) |
250 (113) |
3.00 (76) |
VC119 | 12.5 (318) |
 |
PA125-S-3 | 500 (227) |
500 (227) |
250 (113) |
3.13 (80) |
VC125Q | 13.0 (330) |
 |
PA140-S-3 | 700 (318) |
700 (318) |
350 (159) |
2.50 (64) |
SR140 |
14.5 (368) |
| The DP series of
vacuum pad attachments are suitable for handling heavy, rigid to
semi-rigid loads. They feature rugged deep lipped rubber sealing rings
that are bolted on between two metal plates to handle heavier loads with
security.
Note: Not for use on thin materials. |
|
|
|
|
|
Single Pad Vacuum Lifting Attachments |
|||||
| Product
Photo (Click to Enlarge) |
Vacuum
Lifting Attachment No. |
Rated
Load Capacity* lb (kg) |
Headroom Added to Generator (Bottom of Pad to Mounting Holes) in. (mm) |
Replacement Seal No. |
Vacuum Seal Dia. in. (mm) |
 |
PA145-S-3 | 750 (341) |
5.25 (133) |
SR-145M | 14.50 (368) |
 |
PA155-S-3 | 1000 (454) |
5.25 (133) |
SR-155M | 17.25 (438) |
 |
PA185-S-3 | 1300 (590) |
5.25 (133) |
SR-185M | 18.50 (470) |
 |
PA195-S-3 | 1550 (703) |
5.25 (133) |
SR-195M | 19.50 (495) |
 |
PA215-S-3 | 2000 (907) |
5.25 (133) |
SR-215M | 22.00 (559) |
 |
PA235-S-36 | 2300 (1043) |
4.50 (114) |
SR-235M | 24.00 (610) |
*The
cup capacities shown above are based on 24"Hg at sea level with a safety factor
of two (2) in the horizontal (flat) position.
Rated Load Capacities are
estimated; actual capacity will vary based on the load surface and the level of
vacuum.
Click Here for More Information about Vacuum Generators
| ||||||||